Building Tips, Suspension Set Ups, Conversion Parts .... Build to your Heart's Content!
sabreguy
Posts: 2915 Joined: June 1st, 2007, 5:07 pmLast active: Location: Middle of the Freakin Mojave Desert!
Post
by sabreguy January 24th, 2010, 8:39 pm
88CR500
robertg
Posts: 299 Joined: September 7th, 2008, 11:03 amLast active:
Post
by robertg January 25th, 2010, 5:09 am
That's nice. Do your rads clear your Y?
hoofarted
Posts: 2628 Joined: July 2nd, 2007, 8:48 amLast active: Location: Rancho Cucamonga, CA
Post
by hoofarted January 25th, 2010, 7:30 am
Looks clean so far!
The CR500 is an acquired taste. If you don't like it, acquire some taste...
xr650killer
Last active:
Post
by xr650killer January 25th, 2010, 4:08 pm
Thanks for the help on that dont know why it didnt work.
xr650killer
Last active:
Post
by xr650killer January 25th, 2010, 5:14 pm
It clears by 3/16 of an inch close one.
asteroid500
Posts: 1047 Joined: January 5th, 2009, 1:29 amLast active: Location: Australia Melbourne
Post
by asteroid500 January 25th, 2010, 5:21 pm
Wow a carpeted and furnished workshop.
Nice work mate.
"not speeding officer".....qualifying
xr650killer
Last active:
Post
by xr650killer January 25th, 2010, 5:30 pm
Real close to the beer too.
RideRed
Last active:
Post
by RideRed January 25th, 2010, 10:15 pm
Glad to see you over here! I plan on coming up on Wed or Thurs.
xr650killer
Last active:
Post
by xr650killer January 30th, 2010, 11:04 pm
Last edited by xr650killer on February 20th, 2010, 6:51 pm, edited 1 time in total.
xr650killer
Last active:
Post
by xr650killer February 20th, 2010, 5:16 pm
Sarted the mounts
AlisoBob
"Hoon-father"
Posts: 15405 Joined: May 31st, 2007, 6:39 pmLast active: Location: Aliso Viejo Ca
Post
by AlisoBob February 20th, 2010, 5:32 pm
That actually looks good.
xr650killer
Last active:
Post
by xr650killer February 20th, 2010, 5:59 pm
Thanks BOB
Roostius_Maximus
Site Admin
Posts: 4641 Joined: November 16th, 2007, 3:24 pmLast active: Location: Mt Nebo, Manitoba, Canada
Contact:
Post
by Roostius_Maximus February 20th, 2010, 6:19 pm
the fit looks good, better than ridereds fit,
could be the angle that makes it look bad, looks like he wants to butt weld it, i'd heard he was ordering more filler rod
xr650killer
Last active:
Post
by xr650killer February 20th, 2010, 6:35 pm
You guys that is just a moch up that he is doing.
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pmLast active: Location: Cumming, GA
Post
by Mik329 February 21st, 2010, 5:06 am
lower engine mounts look good!
xr650killer
Last active:
Post
by xr650killer February 21st, 2010, 5:09 am
Thanks going to work on the upper ones today.
xr650killer
Last active:
Post
by xr650killer February 22nd, 2010, 1:09 pm
HrcRacing
Posts: 716 Joined: October 5th, 2007, 11:22 pmLast active:
Post
by HrcRacing February 22nd, 2010, 7:28 pm
Very nice.
xr650killer
Last active:
Post
by xr650killer March 15th, 2010, 8:09 pm
CR500R7
Posts: 2542 Joined: April 26th, 2009, 3:41 amLast active: Location: South Australia
Contact:
Post
by CR500R7 March 15th, 2010, 11:50 pm
Looks good, but how do you know when the invisible chain is tight enough.
Jack Schitt
xr650killer
Last active:
Post
by xr650killer March 16th, 2010, 4:18 am
Did not say it was all done but i will have all the rest of the parts at the end of this week.
gumption
Posts: 34 Joined: January 3rd, 2010, 3:56 pmLast active: Location: Cairns Australia
Post
by gumption March 16th, 2010, 5:23 am
juddy
Posts: 182 Joined: May 10th, 2008, 6:08 amLast active: Location: Western Australia
Post
by juddy March 16th, 2010, 7:07 am
Like ya work mate.Good to see more people using complete new cradles now
