oggos CR500AF supermoto build
oggos CR500AF supermoto build
right boyz i know its very early on but i wanted to take a few snaps , motor should be here within 10 days so i can start chopping the frame ....
i cleaned most of the crap off the frame , took me an hour with petrol , caked on it was .... so the frame now has centre stage in my little nest cause my KTM is ready for 09
i cleaned most of the crap off the frame , took me an hour with petrol , caked on it was .... so the frame now has centre stage in my little nest cause my KTM is ready for 09
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
nice pw, I found a white '85 with red trim so i allowed it in the garage
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
- eyesky2002
- Posts: 492
- Joined: October 30th, 2007, 8:31 am
- Location: SW Iowa
- Contact:
cheers boyz for the vote of confidence
here is some of the plans :
- frame , swinger and subframe , powder coated black satin
- Forks , lower stancions Black nitride
- beringer 4 pot set up
- hopefully Ohlins rear shock
- talons laced with excels (17")
- Pro Circuit expansion & end can
- Cr250 igintion (cdi, flywheel,stator and coil)
- GMX oversized Rad's
- samco hoses
- no airbox !! , gona go with a K&N (dyno'd then to jet)
- TAG tripples or equvalent
- sunline foot rest
- Quick shifter (AFAIK i can get one made up)
- step out the seat
- more bling , like clutch & flywheel covers , twin walls , GPR damper
etc etc etc ... its gona be over time i cant do it any other way , funds dont allow me
here is some of the plans :
- frame , swinger and subframe , powder coated black satin
- Forks , lower stancions Black nitride
- beringer 4 pot set up
- hopefully Ohlins rear shock
- talons laced with excels (17")
- Pro Circuit expansion & end can
- Cr250 igintion (cdi, flywheel,stator and coil)
- GMX oversized Rad's
- samco hoses
- no airbox !! , gona go with a K&N (dyno'd then to jet)
- TAG tripples or equvalent
- sunline foot rest
- Quick shifter (AFAIK i can get one made up)
- step out the seat
- more bling , like clutch & flywheel covers , twin walls , GPR damper
etc etc etc ... its gona be over time i cant do it any other way , funds dont allow me
right i suppose this is where is starts , not much done , but cut the frame , just need to trim the down spar , and make up mounts , should have them done by the weekend , then i will sort out the welding
my bulldog being nosey too
motor stripped a bit , waiting for my replacement crank case & cylinder then i will build it , oh and some internals to arrive
my bulldog being nosey too
motor stripped a bit , waiting for my replacement crank case & cylinder then i will build it , oh and some internals to arrive
happy days dude u will win the race to finish , i have too much to get , but u never know we both might be doing flid fest on cr500af's, the rest of my motor arrived today in ireland , customs have it , so a few days before i get it , i hope to get stuck into it next week , just finished off a crf150 and need to sort out 625smc , then i will finish the fabrication on the cr500 , also have a 525sx to rebuild the motor on in the next few weeks ... wheels should be here too , collecting upper fork tubes hoepfully friday , its all up in the air at the minNeilios wrote:Any progress Ian??
Sorted a welder for my frame at the weekend!! On track for Rowrah.