A quick "How ya'Do", and a photo would be nice.
teemtrubble
Posts: 2269 Joined: October 11th, 2007, 2:15 pm
Location: simi valley, ca
Post
by teemtrubble » May 29th, 2008, 8:08 pm
Hey Bruce I just sent you a PM about that pipe.
Mike
teem trubble works CR500
(Gen 3 125+CR500 motor)
If I wanted a Yamaha I would have bought a piano!
iggys-amsoil
Posts: 3602 Joined: June 1st, 2007, 6:09 pm
Location: Just North of March Airfield CA
Post
by iggys-amsoil » May 29th, 2008, 9:59 pm
I think Flexx bars only come in 12 or 14 unless 10's are newer. I have 12's.
xr680r
Posts: 119 Joined: May 18th, 2008, 4:14 pm
Location: Southern California
Contact:
Post
by xr680r » May 30th, 2008, 6:57 am
Ya, I was on their site and now they sell 10 degree bars. I have a fused left wrist so the less bend puts a little less stress on that wrist. I don't know if it is that big of a difference.
xr680r
Posts: 119 Joined: May 18th, 2008, 4:14 pm
Location: Southern California
Contact:
Post
by xr680r » May 30th, 2008, 7:01 am
Can't figure out where to click to view my PM's. I thought I had been there once but, I slept sense then and now I don't have a clue where to go.........
There a no Gold Rims......wonderbra........
teemtrubble
Posts: 2269 Joined: October 11th, 2007, 2:15 pm
Location: simi valley, ca
Post
by teemtrubble » May 30th, 2008, 7:11 am
805 306-9840
Mike
teem trubble works CR500
(Gen 3 125+CR500 motor)
If I wanted a Yamaha I would have bought a piano!
lewisclan
PVT. 1st Class
Posts: 4804 Joined: June 1st, 2007, 3:34 pm
Location: Yucca Valley CA
Post
by lewisclan » May 30th, 2008, 7:12 am
upper left corner below the photo banner
"the game of life of is not so much in holding a good hand as playing a poor hand well"
lewisclan
PVT. 1st Class
Posts: 4804 Joined: June 1st, 2007, 3:34 pm
Location: Yucca Valley CA
Post
by lewisclan » May 30th, 2008, 7:13 am
but you have to be on the home page and not into a topic
"the game of life of is not so much in holding a good hand as playing a poor hand well"
xr680r
Posts: 119 Joined: May 18th, 2008, 4:14 pm
Location: Southern California
Contact:
Post
by xr680r » May 30th, 2008, 7:20 am
That must be what is wrong. I thought something changed.....I got to go, on my way to PS area. Work needs to be done......
atank
Posts: 301 Joined: April 8th, 2008, 6:41 am
Location: Chatsworth Georgia
Contact:
Post
by atank » July 1st, 2008, 9:28 am
Enjoy the site!
xr680r
Posts: 119 Joined: May 18th, 2008, 4:14 pm
Location: Southern California
Contact:
Post
by xr680r » July 9th, 2008, 11:30 am
Thanks, I am starting to get the hange of it.
By the way did the CR500R rider group take a major slow down after this forum started? After finding this group I didn't see the need to try and go back to that group.
AlisoBob
"Hoon-father"
Posts: 15404 Joined: May 31st, 2007, 6:39 pm
Location: Aliso Viejo Ca
Post
by AlisoBob » July 9th, 2008, 11:33 am
xr680r wrote: ...did the CR500R rider group take a major slow down after this forum started?
It slowed way down before this site ever existed.... Funny what oppression and corrupted power can do....
Glad you feel at home here....
atank
Posts: 301 Joined: April 8th, 2008, 6:41 am
Location: Chatsworth Georgia
Contact:
Post
by atank » July 9th, 2008, 8:20 pm
I would say they did!