Tired of the SHIT grip glue?

NightBiker07 · Post by **NightBiker07** » June 7th, 2012, 7:35 pm

Guy that owns the MX campground I visit often swears by using Enamel-based spray paint as the adhesive. I would recommend using a clear so it doesnt show all over, but I tried it and so far it has a solid hold. He said he has tried everything the market has to offer, and this outperforms by far from what he was saying, and so far, I am a believer.

So, if you are tired of crappy grip glues, give the clear enamel-based spraypaint a try. (Rust-Oleum). Allow for overnight drying for best adhesion.

Post by **MojoScojo** » June 7th, 2012, 9:00 pm

Nobody listens...

http://www.odigrips.com/mxlock-onhonktm ... troke.aspx

TYSTYX · Post by **TYSTYX** » June 8th, 2012, 2:08 am

I use black spray paint to glue my grips on, even on my CBR1000.....works great !!! Before I tried it I checked a couple of dirt and street bike forums and found that a lot of riders use it. Ill never use anything else.

asteroid500 · Post by **asteroid500** » June 8th, 2012, 3:00 am

i sniff glue, but maybe its time i try'd cromeing

http://www.youtube.com/user/500bigbore · Post by **Roostius_Maximus** » June 8th, 2012, 5:47 am

MojoScojo wrote:Nobody listens...

http://www.odigrips.com/mxlock-onhonktm ... troke.aspx

I buy them from moose, Same ODI grip, better marketing.

redrocket190 · Post by **redrocket190** » June 8th, 2012, 5:13 pm

Old school...

Tharrell · Post by **Tharrell** » June 8th, 2012, 5:30 pm

redrocket190 wrote:Old school...

Yup.
Don't have to razor blade the old grips off either

hoofarted · Post by **hoofarted** » June 8th, 2012, 10:21 pm

Tharrell wrote:
redrocket190 wrote:Old school...

Yup.
Don't have to razor blade the old grips off either

X3 - been working fine for me for many years now.

Kuma · Post by **Kuma** » June 9th, 2012, 9:17 am

Auqua Net hair spray

cheapest hair spray you can find, doesnt hurt to safety wire too.

NightBiker07 · Post by **NightBiker07** » June 11th, 2012, 10:39 am

aqua net also makes great potato cannon fuel.

hoofarted · Post by **hoofarted** » June 11th, 2012, 10:55 am

NightBiker07 wrote:aqua net also makes great potato cannon fuel.

Yeah but it gumms up the internals after a while. Scotch guard works much better!

Kuma · Post by **Kuma** » June 11th, 2012, 12:46 pm

If were changing the subject to spud guns, Propane works great

hoofarted · Post by **hoofarted** » June 11th, 2012, 12:55 pm

Kuma wrote:If were changing the subject to spud guns, Propane works great

Haven't tried propane - but I did do oxy-acetylene...with disastrous results. Boom - no more potato gun - no I wasn't holding it.

http://www.youtube.com/user/500bigbore · Post by **Roostius_Maximus** » June 11th, 2012, 1:09 pm

I'd done that, wrapped that in chickenwire and duct tape to secure the shrapnel. Later we used 3"hydraulic ram cylinders

2strokeforever · Post by **2strokeforever** » June 11th, 2012, 8:34 pm

metered propane and air under pressure, kinda like boost, this one i never went over 20 psi boost cause its plastic and handheld, chamber pressures were already over 300psi

i always wanted to make one out of steel and run real high pressure, but i never got around to it

heres what a 1" long piece of carrot shot out of a 1" barrel can do to a 1" piece of mdf, i never measured but i suspect it was going supersonic

NightBiker07 · Post by **NightBiker07** » June 13th, 2012, 6:06 pm

That shit is awesome!!!

never tried propane, never knew how to get it into the chamber.

Rhino89523 · Post by **Rhino89523** » June 13th, 2012, 6:49 pm

http://www.youtube.com/watch?v=5XcKBmdfpWs

Totally messing with you guys on the video, I've built the guns too, not nearly as well.

BannedCR500Riders.com

Tired of the SHIT grip glue?

Tired of the SHIT grip glue?