Did I get ripped Off Trany Issue

honda02 · Post by **honda02** » April 14th, 2009, 3:38 pm

My trany in my 1995 CR500 was trashed I found a guy that been building them for a while he sold me a trany out of a 1986 CR500 he told me it has a wider ratio trans than the one I have so I purchased it from him.
He also told me he sending a Kit to install it in my 1995 cases including a new Counter shaft sprocket he said my clucth basket will work and so on.

Is this true or I just lost $159.00 for thoses parts all gears and shafts shifter forks and shifter drum.

The trans looked almost new did I just get ripped off or will this 1986 trans work in my 1995 cases with my 1995 clucth.

100hp honda · Post by **100hp honda** » April 14th, 2009, 3:57 pm

your punctuation is horrible, cant hardly understand a thing you tried to say

. i thought i was bad but damn

honda02 · Post by **honda02** » April 14th, 2009, 4:06 pm

I trying wacth my kids at the same time and fat fingers while typing is not a good thing to have.

100hp honda wrote:your punctuation is horrible, cant hardly understand a thing you tried to say . i thought i was bad but damn

http://www.youtube.com/user/500bigbore · Post by **Roostius_Maximus** » April 14th, 2009, 4:52 pm

if you got the sprocket, and the bearing for the output shaft then it'll all fit fine, 86+95 have the same ratio tho

ISBB · Post by **ISBB** » April 14th, 2009, 5:05 pm

u sure bout that cuz danny put an 87 in mine and its close ratio

nmdesertrider · Post by **nmdesertrider** » April 14th, 2009, 5:55 pm

The only thing you got screwed on was that the 95 and 86 have the same ratios. It will work fine in your 95 cases.

Just a side note but replacing all the gears costs about 550$.
Don't ask me how I know

honda02 · Post by **honda02** » April 14th, 2009, 6:39 pm

I was going to redo my 1995 trany but the guy thats doing my motor work told me I mite be better off finding a used trany instead it cost $159.00 including shipping thats why I went this route.

After rebuilding the crank top end Ect this AF is turnning into a money pit project I hope it will be well worth all the headachs.

nmdesertrider wrote:The only thing you got screwed on was that the 95 and 86 have the same ratios. It will work fine in your 95 cases.

Just a side note but replacing all the gears costs about 550$.
Don't ask me how I know

nmdesertrider · Post by **nmdesertrider** » April 14th, 2009, 8:08 pm

I got a used tranny too but the dogs were worn so I just decided to go new.

Believe me I understand being a little short on cash for bike projects.

britincali · Post by **britincali** » April 14th, 2009, 9:55 pm

ISBB wrote:u sure bout that cuz danny put an 87 in mine and its close ratio

87 is not a close ratio.

hoofarted · Post by **hoofarted** » April 15th, 2009, 7:32 am

honda02 wrote: this AF is turnning into a money pit project I hope it will be well worth all the headachs.

If its done right, I am sure you will be happy.

oggo69 · Post by **oggo69** » April 15th, 2009, 8:24 am

why do i get the feeling i know where u got the tranny from ... was it an ebay shop ??

ISBB · Post by **ISBB** » April 15th, 2009, 1:30 pm

britincali wrote:
ISBB wrote:u sure bout that cuz danny put an 87 in mine and its close ratio

87 is not a close ratio.

could have sworn it was.. ehh ohh well.

honda02 · Post by **honda02** » April 15th, 2009, 2:20 pm

After doing some more reading and from others I feel good about the trany I purchased it should all work out now.

dannygraves · Post by **dannygraves** » April 16th, 2009, 4:49 pm

ISBB wrote:u sure bout that cuz danny put an 87 in mine and its close ratio

no, that was an '89

dannygraves · Post by **dannygraves** » April 16th, 2009, 4:52 pm

you might have issues with the output shaft bearing, seal, collar, etc. but you should be able to use your '95 counter shaft and just put all the gears from the '86 on it. the mainshaft will be just fine and work with a newer clutch no problem.

dannygraves · Post by **dannygraves** » April 16th, 2009, 4:56 pm

84-87+93-'01 were the same wide ratio, '88-'92 were close ratio.
'86 and '87 have the same counter shaft and sprocket setup, '85 and '84 have unique clutch and sprocket setups and '88+ all had the same shafts and sprockets, just different 4th and 5th gears.
the '86 and '87 countershaft was a different diameter and had fewer splines. the diameter is the big problem since the bearing is different, the seal is different, the seal collar and seal behind the collar are different. I can't remember right now, but I don't think the O.D. of the c/s bearing and seal were the same, which would mean you cannot you use that '86 counter shaft

dannygraves · Post by **dannygraves** » April 16th, 2009, 5:01 pm

ok, so I just checked and on both the OD of the bearing is 54mm and the seal is 40mm, so you just need to order teh bearing, collar, seal and o-ring for and '86 an it will work.

http://www.youtube.com/user/500bigbore · Post by **Roostius_Maximus** » April 16th, 2009, 7:13 pm

http://www.bannedcr500riders.com/board/ ... php?t=3361

BannedCR500Riders.com

Did I get ripped Off Trany Issue

Did I get ripped Off Trany Issue

Sorry

Reading