The old steelie '00 with an '87 is dead..

britincali · Post by **britincali** » August 30th, 2007, 4:36 pm

100hp honda wrote:you leaving the RTV on top of the cylinder? i didnt have time to clean it off lol. come to think of it, im not sure why i put it on there. never had a leak before with a dry gasket

Yea dawg im all about recycling

lewisclan · Post by **lewisclan** » August 30th, 2007, 4:50 pm

Man that SUCKS

lewisclan · Post by **lewisclan** » August 30th, 2007, 4:55 pm

hey will 88 bottom end work for $300?

britincali · Post by **britincali** » August 30th, 2007, 5:27 pm

Hit him up for me J, do me a favor and PM him my cell

dannygraves · Post by **dannygraves** » August 30th, 2007, 5:39 pm

the '88 will use the newer c/s sprocket, which is a plus, but has the close ratio trans, which I think is a negative on a 500.
otherwise, the same! DO IT!
oh, I found those '87 trans parts and cases earlier, looks good.

iggys-amsoil · Post by **iggys-amsoil** » August 30th, 2007, 6:39 pm

dannygraves wrote: dude! what is it with your stuff falling apart???

You don't really want me to answer that do you?

I'm a cheaper bastard - Brit

Seriously though, bummer. At least the whole motor isn't trashed like that 650.

Rosco-Peeko · Post by **Rosco-Peeko** » August 31st, 2007, 1:58 am

Next time you'll know better than to run Aunt Jamima for tranny fluid. That sucks ass dood! Was there any indication while you were riding?

britincali · Post by **britincali** » August 31st, 2007, 4:20 pm

Rosco-Peeko wrote: Was there any indication while you were riding?

Sometimes when hot or really loaded up like in the sand it wouldnt shift gears, the compression had been low for awhile I figured it was just time for new rings.

Hey MFDB you remember in dumont when we were bending my shift lever thinking that was the issue

britincali · Post by **britincali** » August 31st, 2007, 4:21 pm

I just got off the phone with a guy selling an 89 that hasnt been run for 2 years, the bike looks rough and has no papers but he only wants $350 for it. Im going down to look at it around 5pm.....

pstoffers · Post by **pstoffers** » August 31st, 2007, 5:22 pm

Go Brit go!!!!

lewisclan · Post by **lewisclan** » August 31st, 2007, 6:44 pm

go you fricken cheap bastard

britincali · Post by **britincali** » August 31st, 2007, 10:24 pm

Shes home!

Im gonna clean it and start pulling stuff tomorrow, got her for $340

Anyone wanna buy an 89 roller for $350?

Ported&Polished · Post by **Ported&Polished** » August 31st, 2007, 10:42 pm

That's a great deal, how are the wheels?

britincali · Post by **britincali** » August 31st, 2007, 10:44 pm

Ported&Polished wrote:That's a great deal, how are the wheels?

I havent had a really close look but they look alrite, I'll let you have the wheels, tires and frame... Hell everything apart from the motor and exhaust for $350

Post by **AlisoBob** » September 1st, 2007, 9:35 pm

Cause = Effect

Cause = Effect

Crank and Tranny Junk = Entire bike rattling itself apart on trail

Cause = Effect

Class Dismissed!!

britincali · Post by **britincali** » September 1st, 2007, 10:11 pm

AlisoBob wrote:Cause = Effect

Cause = Effect

Crank and Tranny Junk = Entire bike rattling itself apart on trail

Cause = Effect

Class Dismissed!!

Very very very possible bob

hoofarted · Post by **hoofarted** » September 4th, 2007, 11:38 am

Sounds like Danny's 86 when he 1st got it...not for $350 though!

lewisclan · Post by **lewisclan** » September 4th, 2007, 12:19 pm

Nice find bro

BannedCR500Riders.com

The old steelie '00 with an '87 is dead..