The old steelie '00 with an '87 is dead..

britincali · Post by **britincali** » August 29th, 2007, 11:50 pm

I pulled the steelie apart today to slap on the GSS top end and what do I find.....

So now im thinking WTF???? This top end was rebuilt 2.5 yrs ago with an eric gorr port job...

The main bearings have come apart and I now have 3-5 mm of side play and 2-3 mm up and down play in the rod....

The barrel is on its last overbore and it has 2 deep 4mm wide gashes down the sides, so no hope for another rebore.

Bear in mind I started this bike 5 days ago after it had been sitting for 4 months and it fired up 4th kick, yes the compression was down compared to my AF but she still ran great.

RIP good ole reliable '87

Stoffers is hopefully gonna come through on some good rod and rebuild deals

britincali · Post by **britincali** » August 29th, 2007, 11:51 pm

Oh and a port-porn before and after

lewisclan · Post by **lewisclan** » August 30th, 2007, 6:45 am

Thats why ya got to love the 5er

dannygraves · Post by **dannygraves** » August 30th, 2007, 8:01 am

britincali wrote:Oh and a port-porn before and after

Oh man! port-porn!!! ooohhh!!! you can't show me this stuff at work!!!

britincali · Post by **britincali** » August 30th, 2007, 8:06 am

Its a trip seeing how much bigger and cleaner the GSS port job is, eric gorr did a nice job on the jug on the left but its NOTHING compared to what glen did

britincali · Post by **britincali** » August 30th, 2007, 8:09 am

lewisclan wrote:Thats why ya got to love the 5er

Its tripping me out how well it ran, sure it rattled a little and vibrated a bit but all 500s do! You can tell its been running like that for awhile as all of the bash marks have carbon buildup.

I would have never known untill it ripped apart the crankcase

dannygraves · Post by **dannygraves** » August 30th, 2007, 8:10 am

show us some side by side pics of the bottom, like where the transfer ports and intake ports are, I'm curious to see the differences. I just ported mine myself and am very pleased with how it worked out, but I'm all into seeing everyones port work now

britincali · Post by **britincali** » August 30th, 2007, 8:17 am

dannygraves wrote:show us some side by side pics of the bottom, like where the transfer ports and intake ports are, I'm curious to see the differences. I just ported mine myself and am very pleased with how it worked out, but I'm all into seeing everyones port work now

I will get on it this morning for you Mr graves.

dannygraves · Post by **dannygraves** » August 30th, 2007, 8:38 am

britincali wrote:
dannygraves wrote:show us some side by side pics of the bottom, like where the transfer ports and intake ports are, I'm curious to see the differences. I just ported mine myself and am very pleased with how it worked out, but I'm all into seeing everyones port work now

I will get on it this morning for you Mr graves.

LOL...YEAH, MAKE IT HAPPEN!
DO IT!

britincali · Post by **britincali** » August 30th, 2007, 9:28 am

Here you go sir....

Eric Gorr...

GSS

Glen wins hands down!!!!!

Hellbear · Post by **Hellbear** » August 30th, 2007, 9:35 am

Damn Brit you were Johnny on the spot with those pics. Looks good. Now I can't wait till x-mas.

britincali · Post by **britincali** » August 30th, 2007, 9:37 am

Hellbear wrote:Damn Brit you were Johnny on the spot with those pics. Looks good. Now I can't wait till x-mas.

Its easy when your already workin on it in the garage and the cameras handy

dannygraves · Post by **dannygraves** » August 30th, 2007, 9:39 am

wow, what a difference! glens trasver port look liek the could cut you on the knive edging. the gorr job looks really "wham bam" like the knife edging doesn't go that far in and the gorr porting really didn't remove as much material from those 2 lower intake ports where the meet up with the tranfers. I removed close to as much material from that area as glen on my jug. I should have taken some pics before I installed it, but I was too excited!
LOL
Yeah, I'd have to say Glen is the man, that cylinder looks even better when its next to that gorr porting work.

britincali · Post by **britincali** » August 30th, 2007, 9:42 am

dannygraves wrote: Yeah, I'd have to say Glen is the man, that cylinder looks even better when its next to that gorr porting work.

X100000

I know I keep saying this but I am so impressed with glens work, hes without a doubt the best builder Ive ever had dealings with.

lewisclan · Post by **lewisclan** » August 30th, 2007, 9:48 am

nuf said now get that somebitch running

dannygraves · Post by **dannygraves** » August 30th, 2007, 9:58 am

lewisclan wrote:nuf said now get that somebitch running

seriously! I want to see brit flying off the back of that thing at dumont!!

britincali · Post by **britincali** » August 30th, 2007, 10:01 am

lewisclan wrote:nuf said now get that somebitch running

Yea It'll be running by this afternoon, im gonna JB weld some new rod bearings in and it should be good to go.........

dannygraves · Post by **dannygraves** » August 30th, 2007, 10:02 am

britincali wrote:
lewisclan wrote:nuf said now get that somebitch running

Yea It'll be running by this afternoon, im gonna JB weld some new rod bearings in and it should be good to go.........

LMFAO!!!!!

Rosco-Peeko · Post by **Rosco-Peeko** » August 30th, 2007, 2:37 pm

lewisclan wrote:nuf said now get that somebitch running

No kidding! Quit rubbin it and put er together.

britincali · Post by **britincali** » August 30th, 2007, 2:43 pm

Well it gets worse, I just split the cases and found part of a bearing and a gear dog floating around.....

dannygraves · Post by **dannygraves** » August 30th, 2007, 2:49 pm

britincali wrote:Well it gets worse, I just split the cases and found part of a bearing and a gear dog floating around.....

dude! what is it with your stuff falling apart??? are your cases ok?
might want to start looking into getting a '93+ bottom end...

britincali · Post by **britincali** » August 30th, 2007, 2:53 pm

Heres some more pics, im totally bummed now and have given up finding broken stuff for the day..... Wheres my beer.....

What was in the bottom

Bad bearing

Explains why it was hard shifting sometimes!!!

dannygraves · Post by **dannygraves** » August 30th, 2007, 3:11 pm

was there any other damage from that stuff floating around in there? you can buy that one gear and replace that one bearing no prob.
when you go to replace that bearing, use an impact screw driver, don't even attempt it with a regular screw driver, you'll strip them.

britincali · Post by **britincali** » August 30th, 2007, 3:17 pm

dannygraves wrote:was there any other damage from that stuff floating around in there? you can buy that one gear and replace that one bearing no prob.
when you go to replace that bearing, use an impact screw driver, don't even attempt it with a regular screw driver, you'll strip them.

There is scratching on the case and the shift forks are chewed on the ends, there is an 87 being split on ebay rite now so im gonna try to win the gearbox and crank.

100hp honda · Post by **100hp honda** » August 30th, 2007, 4:34 pm

you leaving the RTV on top of the cylinder? i didnt have time to clean it off lol. come to think of it, im not sure why i put it on there. never had a leak before with a dry gasket

BannedCR500Riders.com

The old steelie '00 with an '87 is dead..

The old steelie '00 with an '87 is dead..