02' CRF 450 Conversion
- eyesky2002
- Posts: 492
- Joined: October 30th, 2007, 8:31 am
- Location: SW Iowa
- Contact:
- eyesky2002
- Posts: 492
- Joined: October 30th, 2007, 8:31 am
- Location: SW Iowa
- Contact:
Alum plate attached with two bolts high out of the way to airbox, then bolt box to subframe. Attach boot to carb and then put subframe/airbox on. Top back of boot will hit the plate, but you will have a 1/4" or so gap on the bottom at the plate. Apply heat to upper outside corner of boot where it hits the top side of the frame, you need to dent the boot in enough to allow it to slide up higher in the shock tower around the shock. This also brings up the bottom back side flush to the plate. Once all that is in place and looking how you want it, mark the outside edge and bolt holes with a sharpie. Take it all back apart and just follow the rest of the steps listed in my build.
Cake!!!!
Cake!!!!
"When your riding your living... Everything else is just waiting!"
MXMotoworx.com
2003 Honda CR500AF
MXMotoworx.com
2003 Honda CR500AF
- eyesky2002
- Posts: 492
- Joined: October 30th, 2007, 8:31 am
- Location: SW Iowa
- Contact:
Yep and....Balaclava wrote:
All i need is my 450 airbox, 450 internal ring. 250 airboot, and 250 outter ring?
3oz of permitex, a jig saw to cut the plate and a hole in theplate and a nice assortment of hardware store bolts and lock nuts to adapt the stuff. Some can standard bolts, but some need to perfectly flat countersunk type.
Just remember basiclly the plate becomes part of the boot once you mount the boot in it. Once you hit that point your should be able to see the final picture and assemble it no problem. This is how Bob did his only he used a thinker piece of acrylic material.
"When your riding your living... Everything else is just waiting!"
MXMotoworx.com
2003 Honda CR500AF
MXMotoworx.com
2003 Honda CR500AF
Wicked dude...i'll get it to go next week...
any idea if a 99 cr 125 boot is the same thing as a 99 250 boot? do they have the same size carb?
http://cgi.ebay.com/ebaymotors/HONDA-CR ... 0229019701
would this work??^^
any idea if a 99 cr 125 boot is the same thing as a 99 250 boot? do they have the same size carb?
http://cgi.ebay.com/ebaymotors/HONDA-CR ... 0229019701
would this work??^^
- eyesky2002
- Posts: 492
- Joined: October 30th, 2007, 8:31 am
- Location: SW Iowa
- Contact:
Not sure if they fit, but they show as different part numbers. You can get a new boot and metal ring for cheaper then that old stuff!!!
http://www.hondaparts-direct.com/fiche_ ... &fveh=3269
http://www.hondaparts-direct.com/fiche_ ... &fveh=3269
"When your riding your living... Everything else is just waiting!"
MXMotoworx.com
2003 Honda CR500AF
MXMotoworx.com
2003 Honda CR500AF
well i got the 98 250 boot and what a difference between the 02 and 98...the 98 is MINT!!! should work no problem...that is deffinately the boot to get...airbox is last thing on my list...but i have a new problem...bike is only testing 95 PSI!!!!!! i think i got fucked crank seals...to get all this way and my top end rebuild doesn't do shit!!! i'm choked...we'll see what happens...
- eyesky2002
- Posts: 492
- Joined: October 30th, 2007, 8:31 am
- Location: SW Iowa
- Contact:
Airbox is done...Sealed up nicely...thanx for all the ideas...honestly if i had to i would NEVER do it this way again...it must have taken 4-5 hours of fukkin grinding and cutting and measuring and drilling, and mocking up, and then more grinding and more drilling...seriously was the most annoying and painful part of this build...but it's DONE!...enjoy...my bike IS FINISHEDDDDD!!!!!!!!
- britincali
- Posts: 8207
- Joined: May 31st, 2007, 7:10 pm
- Location: Barstow, CA
ok...it's finished...Started up in 5 kicks, and runs like a DREAM!...starts up first kick every time now...couldn't be more blown away...i know it doesnt' look as pretty as some of the bikes on here, but that will come in the winter...i only have a month or maybe 2 to ride this thing...the torque is amazing and the bike is so nimble...vibes are next to none...
by the way bannedcr500riders.com, made me one happy mother fucker, and i wish i could buy you all a 12 pack for helping me out...cheers boys...
by the way bannedcr500riders.com, made me one happy mother fucker, and i wish i could buy you all a 12 pack for helping me out...cheers boys...
- eyesky2002
- Posts: 492
- Joined: October 30th, 2007, 8:31 am
- Location: SW Iowa
- Contact:
Now go pound that thing hard and hope it stays together, got to tell you the first few jumps on mine I was a bit concerned on the strength of the welds. But so far so good , no cracks and no loose bolts!!!
Got mine somewhat jetted, loading it up now to see how it does WOT!
Got mine somewhat jetted, loading it up now to see how it does WOT!
"When your riding your living... Everything else is just waiting!"
MXMotoworx.com
2003 Honda CR500AF
MXMotoworx.com
2003 Honda CR500AF
ya i just have to wait for my rear brake allan bolt and my air filter cage to get here and it's complete and ready to tear...i ripped it down the back lane for a couple minutes and i was very impressed...and when i came back i was shaking...the engine has such an amazing sound and power to it...considering i've never ridden a 500 before, i had never heard a dirt bike sound like that...it has the most serious rumble to it...and so far nothing has vibrated off or broke...so we'll see this week...
first ride out in the sand pits was pretty good...no cracks in any welds and i only lost 1 shroud bolt...the thing vibrates pretty hard on the back throttle, basically i think that is the only vibrations i can notice...the way it lugs when it's slowing down...other then that...the bike is SICK...and exactly what i wanted if not more...
alright i was killin it on my 500 lately...i got really nice n' used to the bike...hitting some like 50-60 ft long sand hits, but no ramps...got the courage to hit a ramp...went a little too fast in 2nd gear, bike shot up unlike any other bike i ever rode...wayyyyyy past the landing had to ditch the bike, about 30-40 feet in the air...ended up shattering my left ankle, tib fib and all the joints...and earlier that day my little cousin ended up having the bike take off right from underneath him, and tore a massive gash in his thigh, he went to the hospital about 2 hours before i broke my ankle...4 internal stitches and 10 external...
the cr500 is a psyyyyycho bike....mine is running so intensely that no body wants to even try it...
when i heal up it will remain my bike, even though everyone wants me to get rid of it...hope no one goes through this type of ankle smashing...it's a 6 month couch trip...not to mind a career killer!!! shit happens though....but the bike is unbelievablly powerful...and luckily i only lost a seat bolt and broke my inner exhaust mount...the bike landed on it's wheels...
the cr500 is a psyyyyycho bike....mine is running so intensely that no body wants to even try it...
when i heal up it will remain my bike, even though everyone wants me to get rid of it...hope no one goes through this type of ankle smashing...it's a 6 month couch trip...not to mind a career killer!!! shit happens though....but the bike is unbelievablly powerful...and luckily i only lost a seat bolt and broke my inner exhaust mount...the bike landed on it's wheels...
- eyesky2002
- Posts: 492
- Joined: October 30th, 2007, 8:31 am
- Location: SW Iowa
- Contact: