All Engine, Clutch, Chains, and Sprockets Stuff Here.
fmf2001
Posts: 6 Joined: July 15th, 2008, 10:01 amLast active:
Post
by fmf2001 July 27th, 2008, 4:34 pm
Ok I just got done rebuilding my top end .but now is runs like $hit and has a lot of plow back so i looked at the old piston and is a pro x and has a number on it hm50086 .does anyone know if this is a stock size or has it been bored !!!!!
ISBB
Posts: 1547 Joined: October 25th, 2007, 7:16 pmLast active: Location: Sin City
Contact:
Post
by ISBB July 27th, 2008, 5:34 pm
THe piston size is on the top of the piston.. If you have a ton of blowby sounds like you got the wrong size piston..
97 Steel 500 that wants to be an AFC
fmf2001
Posts: 6 Joined: July 15th, 2008, 10:01 amLast active:
Post
by fmf2001 July 27th, 2008, 6:46 pm
ISBB wrote: THe piston size is on the top of the piston.. If you have a ton of blowby sounds like you got the wrong size piston..
thanks for the info it has been bored i but the wrong piston in it
fmf2001
Posts: 6 Joined: July 15th, 2008, 10:01 amLast active:
Post
by fmf2001 July 29th, 2008, 10:35 am
ISBB wrote: THe piston size is on the top of the piston.. If you have a ton of blowby sounds like you got the wrong size piston..
do you think that it would mess somthing up on my cylinder i put about 15 houers on it
dannygraves
Posts: 8020 Joined: June 1st, 2007, 2:03 pmLast active: Location: Las Vegas, NV
Post
by dannygraves July 29th, 2008, 12:26 pm
you should NEVER have a jug bored without giving the piston to the machinist!!!!
'09 kx450f 4-Poke
Gen-4 trail bike --SOLD--
Gen-3 badass trail/mx bike --SOLD--
Gen-1 built dunes bike --SOLD--
'05 klx110 --SOLD--
'95 pw80
dannygraves
Posts: 8020 Joined: June 1st, 2007, 2:03 pmLast active: Location: Las Vegas, NV
Post
by dannygraves July 29th, 2008, 12:26 pm
If a machinist will bore it without the piston... RUN!
'09 kx450f 4-Poke
Gen-4 trail bike --SOLD--
Gen-3 badass trail/mx bike --SOLD--
Gen-1 built dunes bike --SOLD--
'05 klx110 --SOLD--
'95 pw80
teemtrubble
Posts: 2269 Joined: October 11th, 2007, 2:15 pmLast active: Location: simi valley, ca
Post
by teemtrubble July 29th, 2008, 1:09 pm
How did he know what to bore it to? WTF!!!!
Mike
AlisoBob
"Hoon-father"
Posts: 15404 Joined: May 31st, 2007, 6:39 pmLast active: Location: Aliso Viejo Ca
Post
by AlisoBob July 29th, 2008, 1:09 pm
teemtrubble wrote: How did he know what to bore it to? WTF!!!!
X2
fastkart
Posts: 645 Joined: November 20th, 2007, 10:06 amLast active:
Post
by fastkart July 29th, 2008, 1:23 pm
What if the machinist misread the clearance and made it .03-.04 instead? I can't believe there would be a machinist out there that would do a bore without a piston.
teemtrubble
Posts: 2269 Joined: October 11th, 2007, 2:15 pmLast active: Location: simi valley, ca
Post
by teemtrubble July 29th, 2008, 1:50 pm
I can feel .002 clearance all day long I can't believe someone actually put it together without noticing!
Mike
Exnav
Posts: 1420 Joined: November 4th, 2007, 8:42 pmLast active: Location: St. Louis, Missouri
Post
by Exnav July 29th, 2008, 2:37 pm
fmf2001 wrote: ISBB wrote: THe piston size is on the top of the piston.. If you have a ton of blowby sounds like you got the wrong size piston..
do you think that it would mess somthing up on my cylinder i put about 15 houers on it
At the very least I would have a reputable machinist take a look at what you have and the condition of the jug.
Our "Approved Vendors" section offers guidance on who to use for rebuilds like yours.
Good luck to you....
Money ain't got no owners, only spenders - Omar Little
fmf2001
Posts: 6 Joined: July 15th, 2008, 10:01 amLast active:
Post
by fmf2001 July 29th, 2008, 4:24 pm
dannygraves wrote: you should NEVER have a jug bored without giving the piston to the machinist!!!!
Just to let you know I did not know that it was bored the guy that I bought it form did it and he did not tell me .
iggys-amsoil
Posts: 3602 Joined: June 1st, 2007, 6:09 pmLast active: Location: Just North of March Airfield CA
Post
by iggys-amsoil July 29th, 2008, 5:59 pm
Nice save
Trinity Racing mild porting FMF
62 pilot, EGH needle, 172 main
03 Gen III CR250 frame
2013 Dodger Charger 5.7 Hemi
http://www.prisonplanet.com
Your Amsoil Customer #
350882
TYSTYX
Posts: 1317 Joined: June 25th, 2007, 6:30 amLast active: Location: Dark Side of the Moon
Post
by TYSTYX July 30th, 2008, 5:44 pm
kball1313
Posts: 285 Joined: February 7th, 2008, 1:02 amLast active: Location: van city
Post
by kball1313 July 30th, 2008, 6:05 pm
yikes
lewisclan
PVT. 1st Class
Posts: 4804 Joined: June 1st, 2007, 3:34 pmLast active: Location: Yucca Valley CA
Post
by lewisclan July 30th, 2008, 6:07 pm
good clean up just in time
"the game of life of is not so much in holding a good hand as playing a poor hand well"
"the game of life of is not so much in holding a good hand as playing a poor hand well"