VFORCE2 off a 97 cr500
-
- Posts: 5
- Joined: September 8th, 2014, 8:23 pm
VFORCE2 off a 97 cr500
got a good VFORCE2 reed cage I removed to go with a V3 make offer
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
Bin that vf3, quick!
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
-
- Posts: 5
- Joined: September 8th, 2014, 8:23 pm
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
shallow pedal angle, its crap
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
-
- Posts: 5
- Joined: September 8th, 2014, 8:23 pm
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
I've run and flowed everything out there. The VF3 is by far the worst setup ever.
here are some pictures showing flows, I check them with a boot and carb too and the vf2 is still the best.
https://onedrive.live.com/?cid=BD4AA268 ... E9%2140075
here are some pictures showing flows, I check them with a boot and carb too and the vf2 is still the best.
https://onedrive.live.com/?cid=BD4AA268 ... E9%2140075
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
they don't seal at low rpm, at high rpm the inner pedals contact eachother. They're turbulent, they're body is too long, pedals too thin and pedal angle is too long.
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
Roostius_Maximus wrote:I've run and flowed everything out there. The VF3 is by far the worst setup ever.
here are some pictures showing flows, I check them with a boot and carb too and the vf2 is still the best.
https://onedrive.live.com/?cid=BD4AA268 ... E9%2140075
vf2 better than vf3 for cr500 only? What about cr250 valve reed? You tested them?