A quick "How ya'Do", and a photo would be nice.
BBA
Posts: 33 Joined: February 3rd, 2012, 5:32 pmLast active: Location: Mesa, Az
Post
by BBA February 5th, 2012, 12:03 pm
hello all I have stepped up to the plate and purchased a 2006 crf 250 rolling chassis I am going to put my 1997 motor in it . I have never done this in this is going to be all new any suggestions would be wonderful I would like to send the frame out to have it done so I have receipts anybody know anybody who does that and what the prices are?[/u]
Gmbond
Posts: 381 Joined: September 14th, 2009, 7:17 pmLast active: Location: Ontario Canada
Post
by Gmbond February 5th, 2012, 12:51 pm
Spend a few hours reading some posts, especially the sticky posts in the A/F section. Your questions are answered 1000xs over.
BBA
Posts: 33 Joined: February 3rd, 2012, 5:32 pmLast active: Location: Mesa, Az
Post
by BBA February 10th, 2012, 10:02 pm
thanks, i have. It looks like its a bit tougher to do but worth it when it comes to the handling? i just need to find a fab shop here in arizona to do it.
CR500!
If you understand
Well then
You understand
AlisoBob
"Hoon-father"
Posts: 15405 Joined: May 31st, 2007, 6:39 pmLast active: Location: Aliso Viejo Ca
Post
by AlisoBob February 11th, 2012, 8:49 am
Oakdale is only a trip to UPS away....
BBA
Posts: 33 Joined: February 3rd, 2012, 5:32 pmLast active: Location: Mesa, Az
Post
by BBA February 11th, 2012, 3:23 pm
I know what brown can do for me!
CR500!
If you understand
Well then
You understand
BBA
Posts: 33 Joined: February 3rd, 2012, 5:32 pmLast active: Location: Mesa, Az
Post
by BBA February 11th, 2012, 6:14 pm
AlisoBob wrote: Oakdale is only a trip to UPS away....
how much do they charge? where are they located. I do want this done right. will be keeping this bike for a LONG time...
CR500!
If you understand
Well then
You understand
pstoffers
Posts: 1652 Joined: May 31st, 2007, 8:04 pmLast active: Location: Oakdale, CA
Post
by pstoffers February 11th, 2012, 6:18 pm
I'm in Oakdale Ca give me a call @ 209-480-7900 or pm me your # I'll call you
Paul
BBA
Posts: 33 Joined: February 3rd, 2012, 5:32 pmLast active: Location: Mesa, Az
Post
by BBA February 11th, 2012, 6:30 pm
self portriat! late night glamis!
CR500!
If you understand
Well then
You understand
BBA
Posts: 33 Joined: February 3rd, 2012, 5:32 pmLast active: Location: Mesa, Az
Post
by BBA February 11th, 2012, 6:33 pm
CR500!
If you understand
Well then
You understand
BBA
Posts: 33 Joined: February 3rd, 2012, 5:32 pmLast active: Location: Mesa, Az
Post
by BBA February 11th, 2012, 6:35 pm
CR500!
If you understand
Well then
You understand
asteroid500
Posts: 1047 Joined: January 5th, 2009, 1:29 amLast active: Location: Australia Melbourne
Post
by asteroid500 February 11th, 2012, 11:14 pm
welcome bud
"not speeding officer".....qualifying
BBA
Posts: 33 Joined: February 3rd, 2012, 5:32 pmLast active: Location: Mesa, Az
Post
by BBA February 12th, 2012, 6:51 am
Thank you thank you. This place is like a library for CR500's......
CR500!
If you understand
Well then
You understand
Roostius_Maximus
Site Admin
Posts: 4641 Joined: November 16th, 2007, 3:24 pmLast active: Location: Mt Nebo, Manitoba, Canada
Contact:
Post
by Roostius_Maximus February 12th, 2012, 7:02 am
BBA wrote: Thank you thank you. This place is like a library for CR500's......
No, this is the hustler humor of cr500s and all that is good
