BannedCR500Riders.com

ok here's where im at.....
hopefully my mate will sell me his 2001 CR250








All advise would be greatly appreciated

Could someone please fill me in on the pro's and cons that are associated with the different gen frames.. Where is the best place to learn about this...

2strokes4ever wrote:Could someone please fill me in on the pro's and cons that are associated with the different gen frames.. Where is the best place to learn about this...

Just go the the Aluminum Frame Conversion section of this forum. The question comes up quite often.

Try using different search terms too. Tons of info in the AF section. Good luck on your build.

just go to the AF section and scroll through the threads. tons of info there

check your lower end main bearing in your crank, your crank looks rough, and drill some relief holes in you new piston or releive your exhaust bridge after you get that mess cleaned up on your cylinder. good luck on your build

Go to the AF / BEER CANS section and scroll to you get to,
Sticky: For completed bikes of all generations, CLICK HERE!
You will find a SHIT LOAD of info in there.
The whole section won't let you down though.
If you get the 01 250, look for gen2 250 info mainly.
Good luck with the build.

Crank and jug has been sent away, and am picking up Cr250 2001 today for close inspection, apparently the swingarm has a crack and so does the motor, we will see.. Anyway im looking for a Honda oddessy in Australia so i can put the CR250 motor into can any one point me in the right direction.

One more thing im uneducated with, is the year differences between the different generations of frames, also are the 2 stroke frames of the same year the same as the four stroke frameof the same engine capacity etc etc....

I wonder if i can make itlook something like this



That may be a budjet issue

gen1 97-99 CR250 98/99 CR125
gen2 00/01 CR125-250
gen3 02-07 CR125-250 02-04 CRF450
gen4 04-08 CRF250 05-08 CRF450
gen5 09- CRF250 / CRF450
Could be wrong, I am sure someone will tell me.
The gen3 CR250 is similar to the gen3 CRF450, but is not the same frame.
The gen3 CRF450 is based on the gen3 CR250.
The rest are completely different.
That pic is of a gen4 CRF250 conversion.
Ask Danny about converting one of those.
This should be in the BEER CAN section anyway.

2strokes4ever wrote:I wonder if i can make itlook something like this

What, so you can never ride it again?

if i had the money, i would buy a SH just like that,just to get it filthy...
Too bad im just a middle class citerzen...

Gen III or newer have the most parts availiblity.

does anyone know if a 96 steelie swingarm will fit on a 2001 CR250 af bike

2strokes4ever wrote:does anyone know if a 96 steelie swingarm will fit on a 2001 CR250 af bike

Most likley not, why would you want to do that anyway?

Either weld up the gen1 250 swingarm or by another gen1 CR250 swingarm.
Don't get creative, as soon as you change one thing you will have to change something else.
It soon becomes a nightmare and possibly won't function correctly anyway.
The simple things in life are often the best.

No real flash hey.. The back shock is also rooted cuz the owner did burnouts on it after he discovered what had happened, he wants $800 for it, the motor still runs but the left hand side crank case is cracked (no oil leaks)...

Is it worth $800 in Australia

I think it looks ok for $800, besides you won't need the engine for an AF conversion anyway.

moving this to BEER CANS now, looks like im comitted....

Well if you have just been comitted to an insane asylum, could you please send me all your gear before you check in.