Page 1 of 1
SOME UPDATED PICS
Posted: February 8th, 2009, 6:11 pm
by xtremeslide
O.K that is my new bike i want to set up the 0 miles engine in a n AF frame,"still wondering 3 or 4 gen"250 two stroke or a CRF250 of course..
I know that all of you have different opinions so i will post a song and during this, look the pics and after give me your opinion(about the bike conversion),If you use google chrome will be easier,thanks in advance 4all.
Why you like 3 gen conversions or CRF250
http://www.esnips.com/doc/adf1e1f2-e2e4 ... ing%20Kong
P.S:100 hp i'll kick that tank ASAP
Posted: February 9th, 2009, 9:23 am
by Balaclava
it's a shame those old steelie frames are virtually worthless nowadays cause that's a nice bike...Go with any chassis i personally don't care which you pick, but i'll put it this way:
Cleanest - Gen 3 cr250 conversion,
Easiest - Gen 1 cr250,
Most Modern - Service honda uses the Gen 4 250F if you want to be exactly like them,
Largest - Gen3 CRF450 conversion,
Something New - Gen5 Crf450 conversion (that's what i wanna see)
Anyways have fun man...
Posted: February 9th, 2009, 11:04 am
by AlisoBob
I still want to see a Air Cooled A/F conversion
Posted: February 9th, 2009, 11:26 am
by pstoffers
AlisoBob wrote:I still want to see a Air Cooled A/F conversion
Bob if you pay for it all build it and ride it
Posted: February 11th, 2009, 12:09 pm
by Roostius_Maximus
X2, Bob you send me the frame and i'll shove this 450 in it
Posted: February 25th, 2009, 10:46 am
by Neilios
Like this!!
Another project in the garage.
Posted: February 25th, 2009, 10:54 am
by oggo69
get the finger out neilos on both projects .... wana race ??
Posted: February 25th, 2009, 10:58 am
by britincali
Thats badass neilios!!!!!
First aircooled AF in the works
Posted: February 25th, 2009, 11:05 am
by lewisclan
Hell ya
Posted: February 25th, 2009, 11:26 am
by AlisoBob
Neilios wrote:
Posted: February 25th, 2009, 11:41 am
by Balaclava
HAHAHAHA bob that's good...
Posted: February 25th, 2009, 12:54 pm
by Neilios
Fcuk me, too many projects and but too much time spent away from home, that picture must be two years old. other projects on the go include CR500AF, 2x XL250 k3's and a Wes Cooley replica. I must learn to start only one project at a time including work and family!!!!!!!!!!!!!!!!!
Posted: February 25th, 2009, 1:14 pm
by Roostius_Maximus
Thats perfect! only thing i got concerned about is reforming the frame for that dammn left kicker
Posted: February 25th, 2009, 1:23 pm
by Neilios
I have already sorted the swinging arm for the upside down operation, as the chain runs on the other side, the kicker clears the frame, its all down to spacing and the splines. I have been Holding the engine for a CR250 Elsinore but the are so bloody expensive it may get use in this frame. Head off and its an easy fit.
Posted: February 26th, 2009, 5:42 am
by Roostius_Maximus
I had to go out to the garage in a -34c windchill lastnight just to look at that 450 enigne i have, that'll be a nice build. I bet the y on a gen3 250 frame doesnt have to be mooved either, am i right?
Posted: February 26th, 2009, 12:26 pm
by Neilios
That frame is a 2004 CRF450, I do have a 250r in the garage though, might have a try one day.