BannedCR500Riders.com

im offering my services to anyone who wishes!

bore & hone next size over with torque plate and plateau finish $60.00 you pay shipping and supply piston.

or if you want to make a appointment i can do it while you wait !!!!!

PM me if interested

im in NOR-CAL





hope this is OK bob!!!!!

not sure if i need permission to post this?

Naaaaaaaaa....... Roosty likes competition...

do it up

blownbillybob wrote:...bore & hone next size over with torque plate and plateau finish

Why dont you post up some photos of your equipment, fixtures, and tooling.

This better not be some kind of bullshit "Ball Hone" deal....

crustyoldballhoners.com

seems glen has started his own site


if blownbillybob can do good work then its all cool. other wise he probly have to join glen on his new site

Lol!!!!! I'll try and get some pics up never posted pics before might need help with that???

whats considered acceptable work. less than .0005 difference between the largest and smallest diameter measurement ?

Is this sorta what you're lookin for?
I made a new friend with a lot of these goodies.

Lol!!!!! I'll try and get some pics up never posted pics before might need help with that???

Here's how to do it.
Copy this link, it's where you store your photos.
http://www.bannedcr500riders.com/galler ... t=0&page=5

I open the reply thread AND that thread at the same time.

Go through the motions to get a pic on that addy.
Click on last uploads and it will be there.
Click on the pic and click it again to get it larger.
Copy the LOCATION.

in your post,

That's all there is to it.
If it doesn't show up you probably forgot the /



Go ahead and try it, post a naked pic of your girlfriend.

100hp honda wrote:whats considered acceptable work. less than .0005 difference between the largest and smallest diameter measurement ?

more like .00015-.0002
I check the new cylinders too, honda is within .0002

pics didnt work tring again later

use [ img ] at the beggining, and [ /img ] at the end, no spaces in the brackets, or inside the brackets

if you have a photobucket account they make it easy to copy the format for sharing each photo, and pasting into the thread

Roostius_Maximus wrote:

100hp honda wrote:whats considered acceptable work. less than .0005 difference between the largest and smallest diameter measurement ?

more like .00015-.0002
I check the new cylinders too, honda is within .0002

ya i got a new honda one laying around im going to check for the hell of it. got a couple old used ktm ones to check also. checked one already, within .0004 and i measured in about 20 different spots. have no idea the hours on it though. gotta be several years old im thinking, possibly original maybe but i dont know.

i've had some come in that were 90mm and needing a bore, they measured like they had .004 wear, but once i get sizing them ive found them crooked, one had to go 91mmm

Those are the plateau brush set that is on the mandrel now they are $360.00 a set

I also have stones starting 150,220,280,400,600,plateau to hone out the cyl to the proper finish

is that a double decker torque plate ? badass

What do you use for honing oil??

The torque plate is one piece steel the line you see is my locating register for when I mount it in the lathe to machine the bottom of the cyl. It just makes it easier and faster to dial in the bottom

For honig oil I use general honing mineral oil with sunnen MAN-C concentrate additive

Roosty uses pure Canadian Maple Syrup, filtered through Ami Houdes panties....

So your saying she leaks maple syrup filtered threw her panties????

Now that's what I call a real Canadian AAAA!!!!!!!!!!!

She's also the Canadian Womens MX Champion....

finish hone with 400 grit

finish hone with 400 grit and plateau

finish hone with 400 grit

finish hone with 400 grit and plateau


notice how the plateau finishes are alot more shinier then the standard finish.
if you drag your finger nail down the standard finish it feels rough and grabs your nail on the plateau finish its like sliding your nail across a piece of glass you would think the rings wouldnt seat but they do this is what a brush plateau finish should look and feel like!!!!



heres one of my exhaust ports




the center bridge looks crooked as fuk in the pics but is really pretty strait

looks good

ah LIL!! port work!!!