Posted: May 5th, 2008, 7:00 am
MFDB does kinda look like beavis, huh?! Just taller and skinnier! 
BannedCR500Riders.com
Addressing the survival of the legendary CR500!
https://www.bannedcr500riders.com/
dumb question time: rear wheel bearings.
Page 2 of 2
Posted: May 5th, 2008, 10:42 am
Beavis is WAAYY cooler then me...and better looking...
Posted: May 5th, 2008, 10:43 am
Posted: May 5th, 2008, 12:41 pm
Are Beavis and Butthead not the Mods for this site? 
Posted: May 5th, 2008, 12:59 pm
Dude, your avataar is out of control...LOL might want to scale it down a bit...CRMOE500 wrote:Are Beavis and Butthead not the Mods for this site?
Posted: May 5th, 2008, 3:50 pm
...says the man with the second largest avatar.M.F.D.B. wrote:Dude, your avataar is out of control...LOL might want to scale it down a bit...CRMOE500 wrote:Are Beavis and Butthead not the Mods for this site?
Obvious avatar envy.
Heed your own advice eh?
Posted: May 5th, 2008, 6:12 pm
Actually, I have no idea how to scale down a gif, can you??
Posted: May 5th, 2008, 6:47 pm
send it my way i might be able to do sometin with it.. 
Posted: May 5th, 2008, 6:52 pm
Try this on for size.
Posted: May 5th, 2008, 7:13 pm
WTF all the avitars I submit must be a puny 150 x 150 MAX !
What gives?
"Skiddy"
What gives?
"Skiddy"
Posted: May 5th, 2008, 8:57 pm
if you UPLOAD your own avatar it has to be sized... if you link to the avatars url you can get away with bigger however its nice to try and keep them all the same. I believe mojo was workin on a way around that so EVERYONE had to keep them at 150x150.. dont know where he got with that though.
Posted: May 5th, 2008, 9:02 pm
ISBB is the freekin' MAN!ISBB wrote:Try this on for size.
Posted: May 5th, 2008, 10:01 pm
I have no idea on how too change avatar size.
I just found the picture, put in the url, and was a little shocked at the results
.If some one tells me how too change it, or do it for me then no problem.I just thought the size would be changed automaticaly.
I just found the picture, put in the url, and was a little shocked at the results
.If some one tells me how too change it, or do it for me then no problem.I just thought the size would be changed automaticaly.Posted: May 5th, 2008, 11:44 pm
Grassyass holmes...ISBB wrote:Try this on for size.
Posted: May 6th, 2008, 10:06 am
save the picture to your computer... resize it.. then use the upload your own photo feature in your control panel.CRMOE500 wrote:I have no idea on how too change avatar size.
I just found the picture, put in the url, and was a little shocked at the results
Yer welcome MFDB
Posted: May 7th, 2008, 2:03 pm
After riding all day sunday{first run this season} I never had one issue running the bike without the outer bearing retainer.The bearing is tight in the rim and hasn't budged.Thats a big relief because I thought the rim needed replacing.
Last year I found enough traction too pull the air valve through the rim.So after watching a few vids I pulled half the tire off too find the valve.Pry bars was all I had but I succeded with no leaks!The tips in the videos go along way in making the job a whole lot easier.Maybe it wasn't my day, but for the life of me I could not get that damn valve back into the rim.Theres just no room for my big fingers.
Moms idea of tieing a string too the valve pulled through! 
Last year I found enough traction too pull the air valve through the rim.So after watching a few vids I pulled half the tire off too find the valve.Pry bars was all I had but I succeded with no leaks!The tips in the videos go along way in making the job a whole lot easier.Maybe it wasn't my day, but for the life of me I could not get that damn valve back into the rim.Theres just no room for my big fingers.
Moms idea of tieing a string too the valve pulled through! Posted: May 7th, 2008, 4:59 pm
need to snug down or replace your rim locks then if your slippin valve stems like that.. I have run mine completely flat for quite a while and the valve stem never pulled free.. Gotta love dumont and cheap paddles.. must have gone threw one every other trip.. always blowin up a tube.. Then i invested in Ultra heavy duty tubes.. and not a problem since
Posted: May 7th, 2008, 11:02 pm
ISBB wrote:Then i invested in Ultra heavy duty tubes.. and not a problem since
Posted: May 7th, 2008, 11:10 pm
I have ultras in both bikes now, they are a bitch to install on the 19s 
Posted: May 8th, 2008, 8:51 am
After that experience I double nutted the rim locks so they won't work loose.I also put one on the valve, but now that I think about it's coming back off.If the tube wants to move I don't want the valve being ripped off.
Posted: May 8th, 2008, 9:02 am
CRMOE500 wrote: If the tube wants to move I don't want the valve being ripped off.