Nitrous setups

All Engine, Clutch, Chains, and Sprockets Stuff Here.
Post Reply
User avatar
dannygraves
Posts: 8020
Joined: June 1st, 2007, 2:03 pm
Location: Las Vegas, NV

Post by dannygraves »

britincali wrote:
lewisclan wrote:No he wont hit a car but maybe a bike

Been there done that at dumont, not a fun experience.
LMAO!!!!!!!!!! :rotfl:
'09 kx450f 4-Poke
Gen-4 trail bike --SOLD--
Gen-3 badass trail/mx bike --SOLD--
Gen-1 built dunes bike --SOLD--
'05 klx110 --SOLD--
'95 pw80
Image
Slomo
Posts: 491
Joined: June 15th, 2007, 6:37 am

Post by Slomo »

Here's what your throttle is going to look like.
I'll send you a couple spares.
You want me to solder on the pigtails?

Oh yeah, check out how high my forks are- turns on a dime :lol:



Image
User avatar
britincali
Posts: 8207
Joined: May 31st, 2007, 7:10 pm
Location: Barstow, CA

Post by britincali »

Well it better friggin look like that when it comes back cos the one im sending ya looks different (no disc on top) but that one looks better :lol: :lol:

I also fully expect a new renthal dual compound half waffle grip to be installed, and the housing powdercoated.
And yes you can install the pigtails.


:birthday: :birthday: :birthday: :nanna: :birthday:
Coolness list by 90cr500guy

Bob's = 50/50
Cepek = cool
Solidbro = cool
Brit = loser
Stoffer = 1 up from Brit
MFDB = cool
Danny = ok
User avatar
AlisoBob
"Hoon-father"
Posts: 15404
Joined: May 31st, 2007, 6:39 pm
Location: Aliso Viejo Ca

Post by AlisoBob »

slomas wrote: Oh yeah, check out how high my forks are- turns on a dime :lol:



:wink:
User avatar
lewisclan
PVT. 1st Class
Posts: 4804
Joined: June 1st, 2007, 3:34 pm
Location: Yucca Valley CA

Post by lewisclan »

its got to be the love for that to slide by Scott, Right on Slomis you are a good dude . :cool:
User avatar
britincali
Posts: 8207
Joined: May 31st, 2007, 7:10 pm
Location: Barstow, CA

Post by britincali »

lewisclan wrote:its got to be the love for that to slide by Scott, Right on Slomis you are a good dude . :cool:


Hell yea hes hookin me up bigtime, if I instaled that switch it would be kickin NOS at just off idle or not working at all lol


There are some damn good peeps and freindships being made on these boards :cool: :cool: :cool: :cool: :cool: :cool:
Coolness list by 90cr500guy

Bob's = 50/50
Cepek = cool
Solidbro = cool
Brit = loser
Stoffer = 1 up from Brit
MFDB = cool
Danny = ok
User avatar
AlisoBob
"Hoon-father"
Posts: 15404
Joined: May 31st, 2007, 6:39 pm
Location: Aliso Viejo Ca

Post by AlisoBob »

Its funny what happens when you let things naturally run their course..

:wink:
User avatar
iggys-amsoil
Posts: 3602
Joined: June 1st, 2007, 6:09 pm
Location: Just North of March Airfield CA

Post by iggys-amsoil »

AlisoBob wrote:Its funny what happens when you let things naturally run their course..
:wink:
:lol:
Trinity Racing mild porting FMF
62 pilot, EGH needle, 172 main
03 Gen III CR250 frame

2013 Dodger Charger 5.7 Hemi

http://www.prisonplanet.com

Your Amsoil Customer # 350882
LOVEMYCR500
Posts: 120
Joined: September 12th, 2007, 9:24 am

Post by LOVEMYCR500 »

hey Slomas, a bit off the subject but after looking at your forks I have a question. To cure the high speed wabbles (head shake) do you pull your forks up like you have there, or do you go the other way? I have my forks sticking up out of the triples I would say .040-.080 thousands. I get the wabbles occasionally.

I ask this beacause I have a new mission in life after coming back from the dunes this past weekend. There were some real fast drag banshee's running on a flat say 200 yard sand strip with a 100 yard shut down. I ran some of them with the old 500 (stock head and port, v-force reeds, bored PJ carb, PC pipe) had to cheat a little on the start to get going even with them but I was only (here's the funny part either way you look at it) getting beat by 5-7 bike lengths. These were alky burning, overriden tranny, high HP drag frame bikes. I could run them down to a fairly respectable bike length loss. This has my wheels turning now. This is why I was asking about swingarm length and how they launch a couple posts ago. I think a nice little drag ported, alky burning CR 500 with about a 8 over swingarm and a 12 paddle could do quite well againist these things. The longer the run the better. This is going to be some high speed runs, hence the question on head shake. Do the aluminum frame bikes have this problem compared to the steel frame versions or is it a matter of fork position in the triples?
Slomo
Posts: 491
Joined: June 15th, 2007, 6:37 am

Post by Slomo »

My forks are that high because my bike is a hillclimber w/ an extended swingarm. Raising them up helps keep the front end down when running shorter.

On a regular bike, the higher the forks, the twitchier the bike.
Go fast sand drags on a stock length bike, I'd lower the forks about flush and try it out.
User avatar
britincali
Posts: 8207
Joined: May 31st, 2007, 7:10 pm
Location: Barstow, CA

Post by britincali »

You get that throttle yet scott?
Coolness list by 90cr500guy

Bob's = 50/50
Cepek = cool
Solidbro = cool
Brit = loser
Stoffer = 1 up from Brit
MFDB = cool
Danny = ok
Slomo
Posts: 491
Joined: June 15th, 2007, 6:37 am

Post by Slomo »

britincali wrote:You get that throttle yet scott?

It's Columbus Day here in America you British wanker.

read..... all us lazy ass federal employees gots the day off :lol:

I have most of my bikes ready to ride.... finally.
100hp honda
Posts: 4394
Joined: July 4th, 2007, 6:57 pm

Post by 100hp honda »

slomas wrote: Go fast sand drags on a stock length bike, I'd lower the forks about flush and try it out.
my machine did the death wobble at gecko road in front of the ranger station. 5th gear wide open racing some goons on 4pokes. by some miracle i didnt go down like a sack of potatoes. ill think twice before doing that again
User avatar
iggys-amsoil
Posts: 3602
Joined: June 1st, 2007, 6:09 pm
Location: Just North of March Airfield CA

Post by iggys-amsoil »

100hp honda wrote:
slomas wrote: Go fast sand drags on a stock length bike, I'd lower the forks about flush and try it out.
my machine did the death wobble at gecko road in front of the ranger station. 5th gear wide open racing some goons on 4pokes. by some miracle i didnt go down like a sack of potatoes. ill think twice before doing that again
Yeah put the forks flush with the top clamp.
Also set the sag to 100mm-110mm. Start at 105mm.
You'll give up some cornering ability, but who needs cornering in a straight line. :lol:

I have notice a little head shack on my AF however the sag is somewhere between 90-95mm for MX tracks.
Trinity Racing mild porting FMF
62 pilot, EGH needle, 172 main
03 Gen III CR250 frame

2013 Dodger Charger 5.7 Hemi

http://www.prisonplanet.com

Your Amsoil Customer # 350882
User avatar
britincali
Posts: 8207
Joined: May 31st, 2007, 7:10 pm
Location: Barstow, CA

Post by britincali »

The chocolate santa just showed up and my kit is here!!!!!!

First thing im gonna do is take the syphon tube out of the bottle, do you use ptfe on all of the AM fittings or not?
Coolness list by 90cr500guy

Bob's = 50/50
Cepek = cool
Solidbro = cool
Brit = loser
Stoffer = 1 up from Brit
MFDB = cool
Danny = ok
User avatar
AlisoBob
"Hoon-father"
Posts: 15404
Joined: May 31st, 2007, 6:39 pm
Location: Aliso Viejo Ca

Post by AlisoBob »

Put the tools down until Uncle Bob arrives....

:roll:
User avatar
britincali
Posts: 8207
Joined: May 31st, 2007, 7:10 pm
Location: Barstow, CA

Post by britincali »

AlisoBob wrote:Put the tools down until Uncle Bob arrives....

:roll:

Im excited tho!!!!!

I just got the battery, some wire, a 30 amp fuse and holder and a 1amp charger so now im good to go :cool:
Coolness list by 90cr500guy

Bob's = 50/50
Cepek = cool
Solidbro = cool
Brit = loser
Stoffer = 1 up from Brit
MFDB = cool
Danny = ok
User avatar
lewisclan
PVT. 1st Class
Posts: 4804
Joined: June 1st, 2007, 3:34 pm
Location: Yucca Valley CA

Post by lewisclan »

AlisoBob wrote:Put the tools down until Uncle Bob arrives....

:roll:
Its all about the love :cool:
Slomo
Posts: 491
Joined: June 15th, 2007, 6:37 am

Post by Slomo »

Didn't get the throttle yet.
USPS or UPS?
User avatar
britincali
Posts: 8207
Joined: May 31st, 2007, 7:10 pm
Location: Barstow, CA

Post by britincali »

I worked on installing the kit for about an hour, so far all Ive managed is messing up the bottle mounting bracket and removing the syphon tube

:hiding:

As bob told me zip ties aint gonna fly im waiting for him now......
Coolness list by 90cr500guy

Bob's = 50/50
Cepek = cool
Solidbro = cool
Brit = loser
Stoffer = 1 up from Brit
MFDB = cool
Danny = ok
User avatar
britincali
Posts: 8207
Joined: May 31st, 2007, 7:10 pm
Location: Barstow, CA

Post by britincali »

slomas wrote:Didn't get the throttle yet.
USPS or UPS?

The finest chocolate santa truck.
Coolness list by 90cr500guy

Bob's = 50/50
Cepek = cool
Solidbro = cool
Brit = loser
Stoffer = 1 up from Brit
MFDB = cool
Danny = ok
Slomo
Posts: 491
Joined: June 15th, 2007, 6:37 am

Post by Slomo »

Ahhhhh, they haven't been by yet.
User avatar
lewisclan
PVT. 1st Class
Posts: 4804
Joined: June 1st, 2007, 3:34 pm
Location: Yucca Valley CA

Post by lewisclan »

Thats because its probably on its way to Folrida
Slomo
Posts: 491
Joined: June 15th, 2007, 6:37 am

Post by Slomo »

Got the throttle today- I'll get the switches pigtailed at work tomorrow and mail everything out.

I think I still have this mount- I'll look tonight.
It's a helluva lot better than what you were planning....
You can have it if you want it.

Image
User avatar
britincali
Posts: 8207
Joined: May 31st, 2007, 7:10 pm
Location: Barstow, CA

Post by britincali »

slomas wrote:Got the throttle today- I'll get the switches pigtailed at work tomorrow and mail everything out.

I think I still have this mount- I'll look tonight.
It's a helluva lot better than what you were planning....
You can have it if you want it.

Image

That bottle looks smaller than the one I have, mines 2 lber. It measures 4.5" across the bottom. If it works that would be kickass!!!!!
Coolness list by 90cr500guy

Bob's = 50/50
Cepek = cool
Solidbro = cool
Brit = loser
Stoffer = 1 up from Brit
MFDB = cool
Danny = ok
Post Reply