cr500 stator

All Engine, Clutch, Chains, and Sprockets Stuff Here.
Post Reply
cr500binks
Posts: 55
Joined: April 12th, 2010, 7:54 am
Location: cornwall, UK
Contact:

cr500 stator

Post by cr500binks »

right guys im in the process of rebuilding my second AF project and the only thing i need to get is a stator as the engine didnt come with one. the engine is a 85 cr500 can i use another cr500 stator or would possibly a cr125 or cr250 stator fit ?

i need advice as this is the last hurdle in the rebuild and once this is done the beast will be ready to ride
if it dont smoke its a joke
User avatar
Nodge
Posts: 527
Joined: October 31st, 2007, 6:12 pm
Location: Saskatchatoon

Post by Nodge »

Swap out the whole works for a CR250 set up.

http://www.bannedcr500riders.com/board/ ... php?t=8044
Yah, I'm from Saskatchetoon!

MRE 02 250/500 conversion, pulse injector, twirp porting, coolhead, MRE ignition, blah blah blah blah... www.millarengines.com
cr500binks
Posts: 55
Joined: April 12th, 2010, 7:54 am
Location: cornwall, UK
Contact:

Post by cr500binks »

i was unsure if the 250 ignition fitted the 85 motor ! but i might end up going down this route if i cant get hold of a 85 stator
if it dont smoke its a joke
User avatar
Nodge
Posts: 527
Joined: October 31st, 2007, 6:12 pm
Location: Saskatchatoon

Post by Nodge »

I have an 85 stator I'd sell you.
It's just sitting on my bench.
Yah, I'm from Saskatchetoon!

MRE 02 250/500 conversion, pulse injector, twirp porting, coolhead, MRE ignition, blah blah blah blah... www.millarengines.com
cr500binks
Posts: 55
Joined: April 12th, 2010, 7:54 am
Location: cornwall, UK
Contact:

Post by cr500binks »

have you, well im after one ! :D
how much do you want for it posted to the uk ?
thinks like that are pretty much non exsistant over here !
if it dont smoke its a joke
User avatar
Nodge
Posts: 527
Joined: October 31st, 2007, 6:12 pm
Location: Saskatchatoon

Post by Nodge »

I'll snap a picture of it, and we can go from there.
Yah, I'm from Saskatchetoon!

MRE 02 250/500 conversion, pulse injector, twirp porting, coolhead, MRE ignition, blah blah blah blah... www.millarengines.com
cr500binks
Posts: 55
Joined: April 12th, 2010, 7:54 am
Location: cornwall, UK
Contact:

Post by cr500binks »

sound bud, get the pic up !
if it dont smoke its a joke
User avatar
Nodge
Posts: 527
Joined: October 31st, 2007, 6:12 pm
Location: Saskatchatoon

Post by Nodge »

Sorry, been working nights, and getting married in a week or so...
Busy busy busy!
The rubber grommet on the wires is a little cracked up, but it was working when it was removed.

Image

Image

Image

Image

Image

Image
Yah, I'm from Saskatchetoon!

MRE 02 250/500 conversion, pulse injector, twirp porting, coolhead, MRE ignition, blah blah blah blah... www.millarengines.com
User avatar
Kuma
Posts: 854
Joined: February 7th, 2010, 8:26 pm
Location: Norco, Cali

Post by Kuma »

Nodge wrote:and getting married in a week or so...
Oh man, sorry to hear that :twisted:

Realy tho, good luck and happyness and all that BS
User avatar
2strokeforever
Posts: 1524
Joined: November 13th, 2009, 1:04 pm
Location: Vernon B.C Canada

Post by 2strokeforever »

flywheel looks rough, pulsar probably too
the 450 will have less power and will be harder to start, and will be heavier, but to make up for it it will require more maintenance.
4stroke=dead fish
User avatar
AlisoBob
"Hoon-father"
Posts: 15404
Joined: May 31st, 2007, 6:39 pm
Location: Aliso Viejo Ca

Post by AlisoBob »

Kuma wrote:
Nodge wrote:and getting married in a week or so...
Oh man, sorry to hear that :twisted:

Realy tho, good luck and happyness and all that BS

[youtube]http://www.youtube.com/watch?v=gSM8Okj_ ... e=youtu.be[/youtube]
User avatar
Nodge
Posts: 527
Joined: October 31st, 2007, 6:12 pm
Location: Saskatchatoon

Post by Nodge »

If binks doesn't want it, I'll put it in the banned junk yard for $0.00 + shipping.
Yah, I'm from Saskatchetoon!

MRE 02 250/500 conversion, pulse injector, twirp porting, coolhead, MRE ignition, blah blah blah blah... www.millarengines.com
Post Reply