BannedCR500Riders.com

http://www.joshua-consulting.fr/forum/IMG_0367.jpg

http://www.joshua-consulting.fr/forum/IMG_0368.jpg

http://www.joshua-consulting.fr/forum/IMG_0369.jpg

http://www.joshua-consulting.fr/forum/IMG_0370.jpg

http://www.joshua-consulting.fr/forum/IMG_0371.jpg

http://www.joshua-consulting ...

Or ... Spock as stolen gasoline ....

AlisoBob you try, you put your bottle in the sun for 2 hours, and then you returned to your home, you'll see the same effect on your drum (evaporation >> pressure >> Gas leak)

Well, improving the 4-pole ....

It will have to cut it I try to test ....

Or 6 poles...



PS, No, I just checked, the rotor ave 4 magnet, therefore, a 6-pole, it does not ...

https://bannedcr500riders.com/images/auto/f1bf13b9afbc3fdca5c8bcbf2c47764c.jpg

AlisoBob, You are sure it fits inside stock flywheel? Because I just take the measurements, and it should look like this:

http://www.joshua-consulting.fr/forum/stator2.jpg

At least for the measures (1mm loan, I did ...

My solution versus a "normal" (most common used) solution ...

http://www.joshua-consulting.fr/forum/IMG_2999d.jpg

The blue lines represent the attachment of the engine, which in my case also reinforces the weld on the bottom 7 or 8cm long.

The red lines represent the junction between the ...

I will weld the red lines in "external welding" and the 2 blue lines "internal welding.

http://www.joshua-consulting.fr/forum/IMG_2998b.jpg

http://www.joshua-consulting.fr/forum/IMG_2999b.jpg

For against, I would not weld on the yellow lines in order to not weaken the legs.

http://www ...

I did not, I fear that it weakens the metal legs to 2 levels of vertical welds. As against the bottom of the tube will be welded to the lower arch.

I'd photoshop a picture with beads to ask your opinion before attacking....

I use an IMS tank, thus wider. I put a 1cm spacers between the frame and the radiators. In this position, the change does not interfere with the tanks or the modified frame.

Hop, tomorrow chamfers and fitting of side plates ......

http://www.joshua-consulting.fr/forum/IMG_2993.jpg

http://www.joshua-consulting.fr/forum/IMG_2996.jpg

http://www.joshua-consulting.fr/forum/IMG_2998.jpg

http://www.joshua-consulting.fr/forum/IMG_2999.jpg

And measurement for the ...

CRF450 2004 = 9.8Kgs

Yes, with a "good" pendulum (pendular??) jig saw at position 0 or 1. Just let cool the blade to not seal it with hot aluminum.

http://www.joshua-consulting.fr/forum/IMG_2970.jpg

2 more...

http://www.joshua-consulting.fr/forum/IMG_2972.jpg

http://www.joshua-consulting.fr/forum/IMG_2973.jpg

Well, I am also currently building my frame .....

Aluminum 6061 T6 3mm thick.

http://www.joshua-consulting.fr/forum/IMG_2962.jpg

In the process of calculating the cuts ...

What you think of this type of build?

http://www.joshua-consulting.fr/forum/IMG_2953.jpg

http://www.joshua-consulting ...

AlisoBob wrote:

_joshua_ wrote:
There is no indication of sex (male or female) on the drawing....

Nigga' please.....

http://befuddled.ca/wp-content/uploads/ ... ticles.jpg

To anyone own offended.... these ARE NOT testicles either.

Translation problem, so I say ...

ender: AP
To: joshua
Subject: sites
Date: Today at 9:29am
Hey Fred/Joshua, nice job on your supreme level of ass-hattery you recently displayed. I like the responses the Banned guys gave you.

You can stay around only as a few such as yourself have proven to have some good contributions, avatar ...

I am not gay, but I can not say that this "position" does not like me with a nice girl .... :wink:

There is no indication of sex on the drawing, and you really learn (and thus find the site of Keith Haring) to finally know the gender of each.

The bathroom of Keith Haring is a good example against ...

My avatar:

http://www.joshua-consulting.fr/forum/joshua.png

My signature:

http://www.joshua-consulting.fr/forum/userbar-2009.01.08-15h37.gif

The "story" :D :


Sender: AP
To: joshua
Subject: your avatar
Date: May 10th, 2009, 2:08pm
Sorry, but I need to ask you to find another avatar that is ...

This is a "lower" pipe...

Yeah.....

AFCR500

problem resolved....