Search found 842 matches
- January 4th, 2010, 7:22 am
- Forum: A/F's Only.... Talk About Your Beer Can, Right Friggin HERE!
- Topic: Cr250 frame
- Replies: 2
- Views: 375
- January 2nd, 2010, 12:18 pm
- Forum: A/F's Only.... Talk About Your Beer Can, Right Friggin HERE!
- Topic: Cr250 frame
- Replies: 2
- Views: 375
Cr250 frame
Anyone got a cr250 frame that could make an engine jig. I already have a crf150r with a crf250r engine. Now I wanta put a cr250 engine in a 150r frame. I need to build the frame first due to money reasons. Lol I hope everyone is good since I haven't been in here In a bit. I have been out tearing aro...
- November 5th, 2009, 6:54 am
- Forum: Shoppers Only!
- Topic: New complete top end
- Replies: 4
- Views: 756
- November 2nd, 2009, 6:58 pm
- Forum: Shoppers Only!
- Topic: New complete top end
- Replies: 4
- Views: 756
- October 29th, 2009, 9:29 pm
- Forum: Shoppers Only!
- Topic: New complete top end
- Replies: 4
- Views: 756
- October 26th, 2009, 10:46 am
- Forum: Shoppers Only!
- Topic: New complete top end
- Replies: 4
- Views: 756
New complete top end
Everything is new oem. Bolts, studs, nuts, gasket kit ,cylinder, head, piston, rings, bearing and wrist pin. 550 shipped
- September 1st, 2009, 8:12 pm
- Forum: Steelie Rebuilds and Overhauls
- Topic: Cr500 Santa!!
- Replies: 6
- Views: 1277
- September 1st, 2009, 1:05 pm
- Forum: A/F's Only.... Talk About Your Beer Can, Right Friggin HERE!
- Topic: 2005 CRF450X CONVERSION (FINISHED)
- Replies: 21
- Views: 1285
- September 1st, 2009, 8:17 am
- Forum: Steelie Rebuilds and Overhauls
- Topic: Cr500 Santa!!
- Replies: 6
- Views: 1277
- August 31st, 2009, 10:05 pm
- Forum: Steelie Rebuilds and Overhauls
- Topic: Cr500 Santa!!
- Replies: 6
- Views: 1277
- August 31st, 2009, 9:26 pm
- Forum: Steelie Rebuilds and Overhauls
- Topic: Cr500 Santa!!
- Replies: 6
- Views: 1277
Cr500 Santa!!
An elf told me that cr500 Santa is gonna swing by the house tomorrow. I have no cookies to leave out so I left a cold miller and a full bong!!
- August 29th, 2009, 4:11 pm
- Forum: Drive Tech
- Topic: WTF with my "NEW" cylinder
- Replies: 11
- Views: 545
http://i277.photobucket.com/albums/kk68/04yamahar1/cyl8.jpg http://i277.photobucket.com/albums/kk68/04yamahar1/cyl7.jpg http://i277.photobucket.com/albums/kk68/04yamahar1/cyl6.jpg http://i277.photobucket.com/albums/kk68/04yamahar1/cyl5.jpg http://i277.photobucket.com/albums/kk68/04yamahar1/cyl4.jpg...
- August 29th, 2009, 1:21 pm
- Forum: Drive Tech
- Topic: WTF with my "NEW" cylinder
- Replies: 11
- Views: 545
- August 28th, 2009, 9:36 pm
- Forum: Drive Tech
- Topic: WTF with my "NEW" cylinder
- Replies: 11
- Views: 545
- August 28th, 2009, 8:35 pm
- Forum: Drive Tech
- Topic: WTF with my "NEW" cylinder
- Replies: 11
- Views: 545
WTF with my "NEW" cylinder
i ordered this from a honda dealership and it came all packaged up from the factory. but what is going on here?
- August 20th, 2009, 8:50 pm
- Forum: Shoppers Only!
- Topic: Wanted!!
- Replies: 2
- Views: 481
- August 18th, 2009, 11:37 pm
- Forum: Drive Tech
- Topic: cylinder question
- Replies: 13
- Views: 408
- August 17th, 2009, 9:21 pm
- Forum: Shoppers Only!
- Topic: Wanted!!
- Replies: 2
- Views: 481
Wanted!!
A tight bottom end motor. Let the jokes begin. Butt (haha) seriously looking for a bottom end motor[/quote]
- August 16th, 2009, 1:28 pm
- Forum: Approved Vendors
- Topic: service honda
- Replies: 4
- Views: 7599
- August 11th, 2009, 10:04 am
- Forum: A/F's Only.... Talk About Your Beer Can, Right Friggin HERE!
- Topic: anyone know these kats???
- Replies: 22
- Views: 1126
- August 11th, 2009, 9:47 am
- Forum: A/F's Only.... Talk About Your Beer Can, Right Friggin HERE!
- Topic: anyone know these kats???
- Replies: 22
- Views: 1126
- August 10th, 2009, 11:40 pm
- Forum: A/F's Only.... Talk About Your Beer Can, Right Friggin HERE!
- Topic: anyone know these kats???
- Replies: 22
- Views: 1126
- August 7th, 2009, 9:59 pm
- Forum: Drive Tech
- Topic: cylinder question
- Replies: 13
- Views: 408
- August 7th, 2009, 4:06 pm
- Forum: Drive Tech
- Topic: cylinder question
- Replies: 13
- Views: 408
cylinder question
if you bought a new cylinder, piston, rings and changed the rings often and kept them within specs would you ever have to bore. also when you get a new piston and rings what is the proper procedure to check ring gap? thanks homies
- August 6th, 2009, 10:41 pm
- Forum: Shoppers Only!
- Topic: drag motor!!!!
- Replies: 8
- Views: 699