BannedCR500Riders.com

I would pay about $90 for a 6061 ignition cover that was a copy of the OEM cover. It would need to retain the OEM gasket. I am not interested in a clutch cover. The OEM is fine with me. There seems to be a lot of interest in custom covers. Shanman’s machinist got it to the point where all he needed ...

try cleaning the carb again. With the little red straw on a can of carb cleaner spray it through all jets, passage ways etc. Make sure nothing is blocked.

dogger sounds like a sweet fix. I wonder if I can do similar on my RZ. It has engine # it just does not corespond with the vin

I have a photo copy of chapter 4 of a cr500 owners manual. Page 17 says .5-.6 mm (.020 - .024)

Not sure what year manual photo copy came from, 99% sure 2001. 99% sure the photo copy originated from SH as it came with the paperwork the previos owner gave me on my 2001 SH

Has anyone had any experience with gettin their number checked. I had my engine # checked against my VIN when I took my 1985 RZ350 in to get the title transferred. It had a clean Florida title. The time AZ MVD required inspections on all out of state title transfers which they no longer do. Now you...

forgot to mention.... NICE BIKE!

Assuming you are in AZ… My suggestion would be to start off at a third party title agency and see what they can do for you. They will be able to give you your options and navigate through the system better. I know a good one that is very familiar with the needs of us off road guys in east mesa, PM i...

I now have 6ea. Gauge Block 4ea. Chaze327 Gauges https://bannedcr500riders.com/images/auto/bcd60262b4ecf063dce002be9a807ad7.jpg $20 ea. for the Block $45 ea. For Gauge and block $5 Domestic Shipping $15 international Can fit multiples in box for same shipping. PM me for address to send the $ to I wo...

Got this in the garage, one some hoon in the phx area just needs to come over and help me figure it out then we could crank out a batch.

I have not tried with OS tank, but my bet Is that it would work.

Buy a tank from some whare with a good return policy. Un pack carefully, and save packing. Just so long as it fits between the spars, and the bottom of the tank does not hit the engine components, the plastic will work.

After repacing my front brake hose, I bleed like I always bleed on autos. Pump up the brake, holding pressure open the bleed, let lever bottom, tighten bleed and repeat like a million times. no more air bubbles. I am using a clear hose attached to bleed nipple. Still is a bit musshy, must have air t...

roost I dig the MRE logo

http://cgi.ebay.com/ebaymotors/Engine-T ... 27afc347ba


Seems like the crew likes the chaze327 gauges so I ordered them. They should be here in 1-5 days.

Still working on the final #'s

I went to Jay's place today and picked up 6 gauge blocks

ID is 5/8"
OD is 3/4"
OD at Barb is .800 (almost 13/16")
Over all length is 3 1/2"
Gauge hole is 3/8" female pipe thread.

checking into getting thermometers. if you are in a hurry and want wo gauge pm me

I have my old brackets I will give +shipping. But trust me they are UGLY!

Jay wants $30 for his brackets that I used for the shrouds. Seems high to me. I sell his 250r (atc / Trx) case saver for $15. Who knows, I guess the brackets take more machine time, or he is not as overstocked on them as he is on case savers. At any rate that is only the shroud brackets. The side pa...

iggys-amsoil wrote:Ok. Link the gauge here so we can go buy one.

The ESR gauge and gauge block

http://www.eddie-sanders-racing.com/Sea ... emperature

The "USA-1" that I put on my bike.. No link yet I will try to get some and put them in the classifieds.

http://cgi.ebay.com/ebaymotors/CRF-450- ... ccessories

not mine

What is the normal or average running temperature in the summer months? THX--Matt don't know on the 500. On my YZ I stay around 190 f racing up oldsmobile at glamis winter time, but far from cold out. Temp goes up in deep sand / slower speed. Richening up the jetting on bottom helps out alot. Remem...

I appreciate the tip and I checked it out. The photo makes it look like the clamps are closer to the radiator than they really are. An optical conclusion of sorts. The hose would also have to overpower (push out of the way) the lower crossover hose to get the clamps to touch the radiator. One may wo...

Clyde, do you feel the thermostat helps the engine warm up to operating temp quicker?

I have verizon.

Comming from mesa az if anyone wants to carpool.

Will be going by bullhead city to pick up a friend.

What is best (cheapest) way to get a pass. For glamis it is cheaper to get one from a local vendor than on site.

Anything else I ought to know about?

Kuma wrote:
Where will camp be?

I would like to go as well but never been to dumont, so the more detailed the better. Maybe someone could get a GPS coordinate on the halloween trip to where the nov. camp will be.

Clyde I believe they are 5/8" next time I go to jay's I will mesure. They were a tight fit but not too bad,